Produkty dla do silników (383)

Sanaxil I - Therm Smoothed mineral coating for interiors and exteriors with potassium silicates with chemical adhesion, anti-condensation, insulation, mould resistant, thanks to the addition of hollow glass spheres. Sanaxil I - Therm due to its mineral nature with chemical adhesion, revolutionizes the concept of adhesion to the support, penetrating deeply into the pores of the wall to then react with its components and form a unique and indissoluble "silicating" whole. With a final appearance similar to civil plaster. The product does not form a film thus avoiding detachment and peeling phenomena, it ensures a permeability to water vapour thanks to its microcrystalline structure of the same porosity as the wall while guaranteeing excellent water repellency. Elasticity and hardness are coupled in maximum degree with a wide choice of colours not alterable over time; characteristics that, combined with the ease and practicality of application, make the product extremely multi-functional, adaptable to any project requirement. Restoring protective coatings based on stabilised potassium silicates, for vertical and horizontal surfaces. All products in the Sanaxil I – THERM series cannot be attacked by mould. Recommended as a finish in "cladding" insulation systems, as it helps to increase the thermo-acoustic and anti-condensation coefficient. Stone, masonry, concrete and any type of plaster. The Sanaxil I - Therm system can be applied directly on surfaces treated with mineral paints or new surfaces. If there are residues of organic paint on the support (washable, solvent-based paints, etc.), before application it is necessary to remove them by stripping or sandblasting, and also never apply on plaster, under the beating sun, on warm or wet walls. During application, cover areas that are not to be painted such as jambs, doors, windows and floors because silicates attack glass, metals, ceramics, glazes, paint, marble and granite. Adverse climatic conditions can impose the realization of adequate protection during the application and drying phase of the coating. Never mix with other non-mineral based paints. NEW SUPPORTS Apply a coat of Protech Fix AC - Therm fixative diluted from 20 to 50% with water depending on the absorption of the support. OLD SUPPORTS On old supports, remove the old paint by brushing, fill in any holes or imperfections in the wall with a suitable filler, proceed with fixing with Protech Fix AC - Therm impregnating agent diluted 20 to 50% depending on the absorption of the support. The product is ready to use if necessary add a little water and stir slowly. Apply a coating layer with a stainless steel trowel with a thickness equal to that of the granules it contains. Pass again with a cutting spatula to remove any excess material. After light drying, pass over with a plastic trowel with rotary movements to compact, even out and achieve the full plaster effect. On large surfaces, it is recommended to apply the product of the same lot and proceed always wet on wet to avoid signs of resumption. Indicative consumption depending on the different particle sizes of Sanaxil I - Therm available: 1 mm GRAIN: approximately 1.6 -1.8 kg/m²; 1.2 mm GRAIN: approximately 1.8 -2.0 kg/m²; 2 mm GRAIN: approximately 2.4 -2.8 kg/m²; 2.2 mm GRAIN: approximately 2.6 -3.0 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 22 kg

Sanaxil Filler Anti-crackling base, based on siliceous aggregates of different particle sizes, potassium silicate, nylon microfibre and specific agents, in a special mix ensuring watertightness, water-repellence, permeability to steam. Available in two different particle sizes, on request. Specific for the reclamation of internal and external vertical surfaces, characterised by significant presence of cracklings from shrinkage (also of width up to 1 mm), for homogenising regularisation in general. It can also be used as a base to obtain a rustic effect of the finish. Particularly suitable for the anti-cracking reclamation of historic buildings. Due to its mineral nature and the chemical adhesion it provides, Sanaxil Filler represents a significant revolution in the traditional concepts of adhesion to supports: it penetrates deeply into the pores, it reacts with the components of the masonry structure creating a homogeneous, indissoluble and breathable "silicated" whole; it does not form films, it is water repellent and resistant to moulds and micro-organisms. When it is applied in combination with paints or putty coats, it substantially improves their durability, because it gives a greater thickness to coatings and paints. Sanaxil Filler is composed of stabilised potassium silicate, silica aggregates and natural pigments. It has high breathability, excellent mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances in general. Subbase micro-smoothing, for subsequent coatings with paint or with putty coat, specific for the anti-crackling reclamation of large vertical surfaces of buildings and condominiums in general. It creates of a thick base to improve the durability of the coating. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". It is recommended that you preliminarily treat the media with the specific fixative Sanaxil Fix (as such, or diluted with water up to a ratio 1:1). Sanaxil Filler should only be used for reclamation and under the conditions described above. It can be applied with a roller or brush, possibly after dilution with 10-15% Sanaxil Fix. Apply from 0.30 to 0.50 kg of Sanaxil Filler per square metre of surface to be treated. Pail 25 kg - Pail 5 kg

Sanafarbe P Breathable, natural, non-toxic paint, for internal and external surfaces, diffusive type, based on lime putty. Mineral-based, active formulation, high natural anti-mildew and anti-condensation capacity, prepared according to the traditional recipes, for use in ecological building interventions and in the restoration of vintage buildings and monuments. Product based on lime putty and natural pigments. Sanafarbe P has a high breathability, remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances in general. Decorative and internal and external restoration paint. The application supports will be free from fouling, powder, non-adhering parts, etc.; existing paints (washable, organic, solvent based etc.) must be removed. A preliminary fixative treatment of the surfaces is always advisable with a consolidating, transparent, Sanaxil Fix primer, based on potassium silicate. The application of Sanaxil Fix can be done by brush, roller or spray: the number of hands required and the dilution ratio with the most suitable water must be determined according to the conditions and absorption degradation of the supports. The admissible dilution range provides for water addition up to a maximum of 1:1 ratio. Apply by brush, roller, spray, in two coats, spaced-apart, one from the other, by about 24 hours. It allows the easy reproduction of traditional finish type: sponging, rubbing, marbling, infilling. Sanafarbe P is dry to the touch after 2 hours, it can be overcoated after 4 hours, while it will be dry in-depth after 8-16 hours. Apply from 0.20 to 0.40 liters of Sanafarbe P per square metre of surface to be painted. Pail 4 l - Pail 14 l

Ringseal T21 Ringseal T21 is a ring gasket made with a special hydro-expansive rubber that reacts upon contact with water, increasing its initial volume. Used in combination with a tubular spacer for metal formwork with a diameter of 22 mm, Ringseal T21 hermetically seals any discontinuities in conduits that could easily settle in the concrete due to the presence of the spacer and which would compromise the impermeability of the masonry itself. The hydro-expansive capacity of Ringseal T21 has been laboratory tested with three different types of water: demineralised, salt and with a highly basic pH (to simulate conditions in contact with concrete). The expansion tests showed a variation in volume ranging from a minimum of around 200% with salt water (three times the initial volume) to a maximum of over 900% with demineralised water. In the standard version the seal RINGSEAL T­21 is designed for tubular spacers with 21.5 mm inner diameter (without external ribs), normally used in the construction industry and usually having an outer diameter of about 24 mm. Given the elasticity of the seal, greater diameters up to about 30 mm are tolerated. Construction of subterranean structures in concrete by metal formwork, where the wall is in direct contact with the ground and where there is the presence of waterproofing layers outside the masonry itself: basements, garages, underground rooms, etc. Manually place the hydro-expansive seal RINGSEAL T­21 around the spacers of the formwork, in a central position. Build the planned formwork using the tubular spacers thus prepared and proceed with the usual operations of casting the concrete. No. 1 Ringseal T21 gasket for each tubular formwork spacer (average 1 - 2 pieces per square metre for metal formworks). Small bag 100 unit

Repar Tix Fine A structural and shrinkage-compensated thixotropic cementitious mortar with a maximum aggregate grain size of 0.6 mm, consisting of high-strength cements, super-pozzolanic fillers, stabilising additives and high-tenacity polypropylene microfibres. The fine grain size and exceptional workability of the mortar render Repar Tix Fine particularly suited to cortical restorations of structures (with the maximum thickness of the single coat being 20 mm) on reinforced concrete and masonry works, for the restoration of concrete requiring an excellent level of surface finishing, operations on the intrados of slabs, even in environments with aggressive exposure (marine, industrial). Manual or spray application with wet curing for the first 48–72 hours. The fine grain size of the premix (maximum grain 0.5 mm) allows a very accurate level of finish and surface smoothing. The structural thixotropic mortar Repar Tix Fine can be advantageously added with 0.25% of Fluid SRA, a special additive capable of reducing both plastic shrinkage and hydraulic shrinkage. Fluid SRA in fact protects the curing of the mortar and, when mixed with Repar Tix Fine, it can be considered a technologically advanced system capable of reducing the rapid evaporation of water from the mortar and promoting the development of hydration reactions. Fluid SRA, thanks to the interaction with some components of the cement, allows to obtain final shrinkage from 20 to 50% lower than the standard values of the Repar Tix prepared with the addition of water alone. Structural smoothing. Restoration, repairs, reconstruction of the concrete cover, construction of reliable and durable coatings of building, civil, hydraulic, industrial, concrete and masonry works. The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, etc., saturated with "saturated dry surface" water. Adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Before restoring them, it is recommended to apply the consolidating re-alkalizing Consilex San on exposed surfaces. Pour 2/3 of the total mixing water into the mixer (about 2.5 liters per bag), gradually add the product and the remaining water, until a homogeneous mixture of the desired consistency and free of lumps is obtained. Take care of the protection and the damp curing of the exposed surfaces. The addition of Bond HG to the mixing water (in the ratio of about 0.5-0.7 kg per bag of product) allows significant improvements in terms of adhesiveness, adhesion, impermeability, workability, moldability and deformation capacity . High coating thicknesses, static requirements, monolithic requirements, etc. they may make it necessary to use suitable reinforcements (electro-welded meshes, etc.) anchored to the substrate with Syntech Profix, Syntech Fix EP or Grout Cable. Approximately 18 kg / m² of Repar Tix Fine for each centimeter of thickness to be created (approximately 1800 kg for each cubic meter). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Repar Steel Two-component cement slurry, modified with flexibilising resins and specific anticorrosive agents for the passivating treatment of oxidised reinforcement rods, in the restoration of degraded concrete. The anticorrosive efficacy of Repar Steel is determined by the high alkalinity and by the superpozzolanic reaction of the components of the anhydrous system, as well as by the presence, in the liquid component (B), of migratory and interfacial corrosion inhibitors, capable of carrying out cathodic and anodic protection, based on organic compounds capable of making ferrous ions unavailable for feeding electrochemical corrosion processes. The polymeric components of the solution also determine further increases in the anticorrosive efficacy, especially against aggressive attacks deriving from chlorides and sulphates, and increase the adhesion between the treated bar and the concrete (adherence test according to EN 15184 in compliance with the UNI EN technical standard 1504 "Products and systems for the protection and repair of concrete structures - Part 7: Corrosion protection of reinforcements"). Passivating protective anti-corrosive treatment for reinforcing rods in restoration works in reinforced concrete. Carefully remove loose rust from the metal surfaces of exposed reinforcing bars by sandblasting or deep brushing until the white metal surface is obtained. This operation is essential to effectively develop the anticorrosive property of Repar Steel. Obviously, to block the advance of the carbonation profile in the concrete, it is essential to complete the restoration with the appropriate restoration mortars: thixotropic (Repar line) or pourable (Grout line). Mix components A and B and continue mixing until a homogeneous, lump-free mixture is obtained. Apply with a brush to the surfaces of the previously prepared reinforcing bars. To prevent the application of the repair mortar from removing the still fresh Repar Steel treatment, wait for the product to harden before proceeding with the volumetric restoration. The minimum recommended waiting time is approximately 6-8 hours with summer temperatures and approximately 12-16 hours with winter temperatures. Do not apply the product with temperatures below 5°C or if it is expected that the temperature may fall below this value during the first 12 hours of curing. From 0.03 to 0.1 kg of Repar Steel for each linear metre of steel bar to be treated. Pail 3.4 kg [A] - Bottle 1.6 kg [B] - Kit: 1 Pail 3.4 kg [A] + 1 Bottle 1.6 kg [B]

Repar SM Bic Fine skim, two-component, thixotropic, rheoplastic, composite , "multipurpose", fast solidifying. Perfect for millimetre and cosmetic smoothing of artefacts and works of concrete in structural and/or functional restoration; also suitable for smoothing façades of buildings with partial or total presence of wall plastic coatings. Repar SM Bic and a plaster end, two-component, thixotropic, rheoplastic, composite , "multipurpose"; based on high-resistance cements, superpozzolanic fillers, hydrodispersed polymeric resins, plasticisers, stabilisers, and anticorrosives, antiallergic additives, selected aggregates, microfibres. The very fine binding matrix, with a high pozzolanic component, together with the special polymers contained in component B, give the applied product a high adhesion to the support, together with a particularly low elastic modulus. The fine grain size and spheroidal morphology of the quartz aggregates facilitate the application of the smoothing compound, especially when used in combination with GFRP meshes (Rinfor System anti-tipping and anti-shattering systems). • Repairs, smoothing, protective and waterproofing coatings, planar regularizations, adhesive coatings, etc., on cementitious supports, walls, cement plasters, concrete floors, even low-absorption coatings (plastic wall coatings, provided they are firmly anchored to the support). • Smoothing of reinforced concrete structures of tanks, tanks and swimming pools, before installing resin coatings or tiles. • Smoothing of beams, pillars and decks of road infrastructures • Rinfor System anti-tipping system on partition walls and infills, in combination with GFRP Armaglass Structura 115, Armaglass Structura 250 meshes and connectors in GFRP Armaglass Connector or in Helix Steel Aisi 304 stainless steel. • Rinfor System shatter-proof system on floors, in combination with Armaglass Structura 250 GFRP mesh, flanges with screws and brackets with plugs. • Regularization and preparation layers of concrete and masonry supports before the installation of carbon fiber FRP systems, both impregnated in situ (fabrics) and glued (sheets). Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Mix the concrete powder (component A) with the polymeric hydrating dispersion (component B), preferably with a mixer at a low number of revolutions, gradually pour the powder into the liquid (in case of manual mixing add the liquid to the powder); continue to mix until a homogeneous lump-free mixture is obtained. The optimal consistency of the product and the consequent physical-mechanical performances declared in this technical data sheet can be reached using 4.5 kg of COMPONENT B for each 25 kg bag. The excess quantity of COMPONENT B (0.5 kg) is particularly useful for priming the substrate, or for wetting the trowel in the final smoothing operation, or in hot and arid environmental conditions where the mixed product is kept at rest in the bucket it may require some light addition of liquid to regain its optimal consistency, thus avoiding uncontrolled water additions. Approximately 2.0 kg/m² of Repar SM Bic for each millimetre of thickness to be made. Bag 25 kg [A] - Plastic can 5 kg [B] - Kit: 1 Bag 25 kg [A] + 1 Plastic can 5 kg [B]

Repar SM Fine skim, monocomponent, thixotropic, rheoplastic, composite , "multipurpose", fast solidifying. Perfect for millimetre and cosmetic smoothing of artefacts and works of concrete in structural and/or functional restoration. Repar SM is a fine plaster, monocomponent, thixotropic, rheoplastic, composite , "multipurpose"; based on high-resistance cements, superpozzolanic fillers, hydrodispersed polymeric resins, plasticisers, stabilisers, and anticorrosives, antiallergic additives, selected aggregates, microfibres. Repairs, finishing coats, protective and waterproofing coatings, planar regularisations, surface coatings, adhesives, etc., on concrete and masonry supports, even in cold weather. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer, add Repar SM and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 15-18% of the weight of the bag. After mixing is completed wait a few minutes before applying. It is recommended to prepare a limited quantity of mixture at a time, to avoid waste. Smoothe the surfaces to be regularised by applying the product with a spatula, sponge float, etc. Approximately 1.65 kg/m² of Repar SM for each millimetre of thickness to be made. Bag 25 kg

Protech Sil I - Therm Spatulated nanotechnological wall coating for interiors and exteriors, anti-condensation, elastomeric, sanitizing, thermal insulator, formulated with hollow glass microspheres (3M Glass Bubble), heat-reflecting based on siloxane resins in aqueous emulsion with high permeability to water vapor, with a similar final appearance to the civil plaster. It allows the creation of thermal insulation with the obvious advantages of recovering the thermal mass from the walls and eliminating bridges and thermal changes in buildings. Protech Sil I - Therm designed above all for buildings and monuments subject to the protection of the Ministry of Cultural Heritage. The binder based on an emulsion of silicones has allowed to develop a microporous filter impermeable to heavy rain, and at the same time permeable to the diffusion of water vapour. Thermal insulation coating that allows the realization of a thermal insulation with the obvious advantages of recovering the thermal mass from the walls and eliminating bridges and thermal changes of the buildings. Due to its high degree of insulation and transpiration, it is widely used to radically solve mould problems, through the synergistic action of fungicide and thermal insulation. It is composed of a water-dilutable silicone resin, acrylic dispersion, with controlled grain size marble grit, fillers, 3M Glass Bubbles, sanitizing additives and pigments, in a content that guarantees the fulfilment of physical parameters such as: permeability, water repellency, CO2 diffusion, etc. Suitable for any type of mineral support, ideal especially on walls where the growth of mould and algae represents a serious problem. Due to its low thermal conductivity, it is particularly suitable for solving problems of mould and algae on walls exposed to areas of shade and high humidity. SUPPORTS ALREADY PAINTED WITH SILOXANIC PAINT Remove any stains and proceed with painting with the siloxane coating (it is always recommended to apply a coat of siloxane impregnating agent). NEW SUPPORTS Apply a coat of siloxane acrylic fixative diluted from 20 to 60% with water depending on the absorption of the support. OLD SUPPORTS ATTACKED BY MOLDS Clean the wall from mould and algae with a steam cleaner, disinfect with Consilex Muffa Cleaner and Consilex Muffa Remover (sanitizer) after a few hours, when the microorganisms have neutralized proceed with the application of a coat of Protech Fix AC - Therm diluted from 20 to 50 % with water. Once dry, proceed with the application of Protech Sil I - Therm. The product is ready to use if necessary add a little water and stir slowly. Apply a coating layer with a stainless steel trowel with a thickness equal to that of the granules it contains. Pass again with a cutting spatula to remove any excess material. After light drying, pass over with a plastic trowel with rotary movements to compact, even out and achieve the full plaster effect. On large surfaces, it is recommended to apply the product of the same lot and proceed always wet on wet to avoid signs of resumption. Indicative consumption depending on the different particle sizes of Protech Sil I-THERM available: 1 mm GRAIN: approximately 1.6 -1.8 kg/m²; 1.2 mm GRAIN: approximately 1.8 -2.0 kg/m²; 2 mm GRAIN: approximately 2.4 -2.8 kg/m²; 2.2 mm GRAIN: approximately 2.6 -3.0 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 20 kg

Protech Sil I Water-repellent, breathable, pigmented, ready-to-use plaster based on siloxane resins dispersed in water. Ideal for the protective coating resistant to water and bad weather in the renovation interventions, both of external facades and of internal environments, of civil and industrial buildings, and in new constructions. Protech Sil I is available in 5 different sizes for the most varied applications: - Very fine (grain ≤ 0.4 mm) - Fine (grain ≤ 0.7 mm) - Medium (grain ≤ 1.0 mm) - Large (grain ≤ 1.5 mm) - Very large (grain ≤ 2.0 mm). "Waterproofing", water repellent, breathable, protective and decorative finish, for masonry surfaces in vintage buildings, subject to protection as "cultural heritage" or otherwise, in restoration, for new buildings, in dehumidifying systems etc. The surfaces of application will be adequately prepared: dry, free from fouling, powder, crumbling parts, incoherent, pre-existing synthetic paints etc. Any lime and/or cement-based plaster, lime painting, compact and anchored, they can be preserved. It is essential to pre-treat with the siloxane fixative Protech Sil Fix. Protech Sil I is ready to use, in the form of thixotropic paste which, after thorough mixing, can be applied immediately. Two layers of application are recommended, each with a thickness not exceeding the size of the calcareous grain contained in the product. After applying the second coat, when the product starts the drying stage, proceed to floating with sponge tool. Indicative consumption depending on the different particle sizes of Protech Sil I available: 1 mm GRAIN: approximately 1.25 -1.40 kg/m²; 1.2 mm GRAIN: approximately 1.40 -1.55 kg/m²; 2 mm GRAIN: approximately 1.85 -2.15 kg/m²; 2.2 mm GRAIN: approximately 2.00 -2.30 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 5 kg - Pail 25 kg

Protech Road Line Fast-drying refractive synthetic paint with excellent coverage and resistance to atmospheric agents, specially designed for painting horizontal road signs. Based on acrylic resin, specific plasticizers loaded with Rutile Titanium Dioxide, synthetic pigments resistant to UV rays, lamellar and crystalline charges, glass microspheres with a high refractive index and a specific mixture of solvents to balance drying in depth and in surface, allows to communicate the safety rules according to the provisions of the highway code both in the urban and extra-urban areas for the center lines, side lines, zebra stripes, stop bands and pedestrian crossings etc. Protech Road Line is specific for road markings on flooring, including roads: asphalt, cementitious substrates, porphyry, etc. Remove all traces of dust. On a dry support, apply Protech Road Line according to the methods described in the instructions for use. Protech Road Line, depending on the equipment and application methods, must be diluted, generally 5%, with a specific synthetic thinner for traffic island paints. Avoid applications in the presence of surface condensation, ice and make sure there is no flaking paint. Stir the product thoroughly before use. Apply 1.30 kg of Protech Road Line per square metre of surface to be painted. Can 25 kg - Can 5 kg - Pallet: 33 x (Can 25 kg)

Protech AC-P Paint based on acrylic resins in aqueous emulsion, for interiors and exteriors, protective lamellar structure which, in addition to having an aesthetic effect, allows maximum filling, transpiration and very high resistance to mechanical and chemical light. The high coverage and expandability make this product extremely easy to apply. The special acrylic resins that compose it allow to obtain a film characterized by a rapid insensitivity to water even during the drying phase, with a consequent reduction of the "snail effect" in the event of atmospheric events. Protective and decorative finish painting of walls, facades, concrete products, plasters, masonry, natural stone, porous substrates in general. For old plasters, pay particular attention to the old pre-existing paints, which must be removed by careful scraping and brushing in order to obtain a healthy and non-friable support; then proceed with the application of Protech Fix AC fixative. When applying on new plasters, it is good practice to insulate the base with acrylic insulator or even better with a white or neutral microemulsion fixative. Avoid windy or cold days when applying. Do not apply on fresh or particularly alkaline substrates, respect a minimum carbonation period of at least four weeks. On large surfaces it is recommended to apply product from the same batch and always proceed wet on wet to avoid signs of recovery. Never operate with temperatures below + 5 ° C. Rainy weather, excessive atmospheric humidity and temperatures below + 8 ° C can greatly compromise drying with the possibility of washing off by rainwater even after several days. . DILUTION (by volume with drinking water) BRUSH 1st COAT: 15% a crossed coat or two coats 12-24 hours apart 2nd COAT: 10%. ROLLER 1st COAT: 10% 2nd COAT: 10%. SPRAY (through specific equipment) 1st COAT: 15/25% 2nd COAT: 15/25%. To avoid filming defects, being resin-based products in aqueous emulsion, the application temperature must be between + 5 ° C and + 35 ° C with relative humidity not higher than 60/70%. Do not apply under the direct action of the sun and wind. Do not apply on fresh or particularly alkaline substrates, respect a minimum drying period of the substrate of at least four weeks. It is also advisable for colored, not to use on large surfaces dyed with different production batches as slight differences between batch and batch are technically possible. Please check the color before application as we will not respond to any disputes regarding the shade of the applied product. From 0.20 to 0.30 liters of Protech AC-P for each square meter of surface to be painted. Pail 14 l

Proband Cold applied water-repellent adhesive tape, composed of a layer with visco-elastic butyl rubber consistency, coated with a polypropylene non-woven fabric, for elastic waterproofing of non-structural joints in balconies, terraces, etc. Size of the strap: 80 mm x 0.9 mm. The Proband non-woven fabric coating is composed of 100% pure polypropylene fibres, with a weight of 30 g/m² and a tensile strength of 45 N. Elastic waterproofing of non-structural joints in balconies and terraces, especially in the protective "kerb" of the connection joints between the screed and the vertical wall. The application supports must be clean, dry, undamaged, cohesive, free from fouling and dust. The strap is provided with a special waxed paper film on the adhesive side. To apply, proceed with the detachment of the protective film and place the strap in its final place, with the adhesive side facing the support. Apply slight pressure with your hand to ensure proper adhesion to the support. Then continue to detach the protective film while unwinding of the roll and setting on site , taking care to avoid the formation of bubbles. 1.1 m/m: 1 metre of Proband for each linear metre, being careful to overlap the rolls of approximately 5-10 cm in correspondence with the edges of the band. Roll 10 m

Syntech Pavistrong A two-component coating with a modified epoxy resin base, specific for protecting concrete surfaces destined to be in contact with aggressive agents or for containing food products and drinking water. Syntech Pavistrong is certified according to EN 1504-2, for the protection of structures in reinforced concrete as well as for food contact, in accordance with the requirements of Ministerial Decree 21/03/73 and subsequent amendments. Syntech Pavistrong is characterized by its excellent chemical resistance to aggressive exposure environments, to alkalis even at high concentration, to medium concentration acids and to the flow of liquids even containing solid suspensions. It is impermeable to water and chemically aggressive agents. It constitutes an effective barrier to the penetration of carbon dioxide and the carbonation of concrete. It is non-toxic, therefore suitable for contact with food and drinking water. It has excellent adhesion to concrete, steel, bricks, stone in general and various materials commonly used in construction. The fluid consistency makes Syntech Pavistrong fast and easy to apply both by brush and roller. Industrial concrete floors. Purification tanks for waste water and related technical rooms. Food tanks, pipes and containers. Digesters and plants for the production of biogas. Coating of canalizations and liquid containment tanks. Water treatment, purification and distribution plants. Containers of acidic and basic substances. Stables, milking rooms, veterinary rooms, slaughterhouses. Analysis laboratories, warehouses, raw material storage areas and production areas. Containers for accidental spills of petroleum products, chemicals and food products. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Apply Syntech Pavicrom when the primer is completely dry and no later than 24 hours from the end of its application. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to first apply the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Thoroughly mix the two components in their respective containers. Pour the can of component B into the can of component A, mix thoroughly for 2-3 minutes. To obtain a perfect mixing use a mechanical stirrer or a suitable tool. The mixture of the two components must be spread within 20-30 minutes, in order to avoid hardening in the can itself. Note that the reaction rate depends on the ambient temperature (at 30 ° C it hardens in 15 minutes). Apply on the surface to be treated, in two coats, within the indicated times, for an indicative consumption of 500-600 g / m². Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Do not dilute the components or the mixture of the two components. From 0.50 to 0.60 kg of SYNTYECH PAVISTRONG for each square metre of surface to be covered, for two coat applications (0.25-0.30 kg per single coat). Can 2 kg [A] - Can 6 kg [A] - Can 1 kg [B] - Can 3 kg [B] - Kit: 1 Can 2 kg [A] + 1 Can 1 kg [B] - Kit: 1 Can 6 kg [A] + 1 Can 3 kg [B]

Syntech RGS A fluid, medium-viscous epoxy adhesive for the structural casting of joints (new conglomerates on existing structures). After careful mixing, the two-component compound must be applied on the existing concrete by brush or roller, a few minutes before applying the new conglomerate (“wet-on-wet”). Construction joints between new and existing concrete, flooring and structures. Sealing and filling of cracks in the concrete (of a magnitude greater than 1 mm). The application surfaces should be suitably prepared and adequately resistant: free from dust, grease, fouling, crumbling and non-adhering parts, free of detected surface humidity, for floorings, moreover, it may be advisable to carry out preliminary shot peening or milling of adhesive surfaces. Add component B to component A taking care to remove all the material from the packaging, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mixture is obtained; add the required load amount (component C) continue to mix until a homogeneous lump-free mixture is obtained. Apply by brush or roller on the surfaces prepared. Spread, or "cast" on site, the subsequent conglomerate, in the range of application defined by the conditions of adherence of Syntech RGS (before it hardens). Apply from 0.30 to 1,00 kg of Syntech RGS per square metre of surface to be treated. Can 3.3 kg [A] - Can 13.4 kg [A] - Can 1.7 kg [B] - Can 6.6 kg [B] - Kit: 1 Can 3.3 kg [A] + 1 Can 1.7 kg [B] - Kit: 1 Can 13.4 kg [A] + 1 Can 6.6 kg [B]

Syntech PU Foam 30 Syntech PU Foam 30 is an expanded polyurethane with a nominal density of 30 kg per m³; it is a closed cell foam, developed using a new generation blowing agent designed to adhere to various supports and capable of providing both excellent thermal insulation and minimizing air leaks. As part of a system, it has been designed as a closed cell, tested and evaluated for use as a composite system to provide a complete air barrier and to provide exceptional performance in reducing heat transfer, achieving incredible benefits such as minimizing the humidity transmission and air leaks. The performance of Syntech PU Foam 30 has been evaluated on iron, sheet metal, steel, glass, concrete and wood as a composite system or together as a single system. Syntech PU Foam 30 guarantees adhesion with excellent support, giving rise to a continuous membrane, without any joints and extremely resistant: - It adapts to any geometric shape - Friend of the environment, they are inert and disposable materials. - Does not weigh down the structure - Low permeability - Better thermal insulation - Reduced thicknesses compared to other insulators - Elimination of thermal bridges - Long life - useful life exceeding 50 years. - Excellent compressive strength - Resistant to biological attack and does not favor the growth of fungi and bacteria. Syntech PU Foam 30 expanded polyurethane is particularly used for: - Thermal insulation on buildings, attics, ceilings - Waterproofing following the use of top covering coating - Coating of foundations - Coating of cisterns and reservoirs - Coating of isothermal vans - Protection of pipelines and pipes - Cold room lining - Coating and protection of sheet metal. All surfaces must be free of contaminants and humidity less than 3%; it must offer a mechanical grip on a solid and non-yielding support. Where necessary, we recommend preparation using shot peening, bush hammering, sanding or hydrowashing. Consult personnel for correct preparation of the support. It is recommended to use, if necessary, primers from the Syntech family and contact the staff for clarification on the most suitable type to use. Syntech PU Foam 30 requires a bimixer system capable of producing pressure over 160 bar and temperatures over 60 °C, equipped with transfer pumps with a 3:1 ratio. Contact the staff for clarification on the best gun to use and details relating to the air system. The two components must be preheated to around 30 C° using heating bands. Syntech PU Foam 30 must be sprayed at pressures that fall within the range of 140 -160 bar and at temperatures that can vary from 35 to 45 °C. It is the applicator's responsibility to correctly calibrate the technical equipment taking into account the combination of nozzles relating to the gun, the length of the hoses and the technical parameters of the spray system. Syntech PU Foam 30 must not be applied in thicknesses greater than 3 cm per coat. The next step should not be carried out before 30 minutes have passed since the previous application, giving the material time to cool. Approximately 0.350 kg of Syntech PU Foam 30 for each square meter of surface to be coated and for each centimeter of thickness to be created. Barrel 250 kg [A] - Barrel 215 kg [B] - Kit: 1 Barrel 250 kg [A] + 1 Barrel 215 kg [B]

Syntech Pavicar Two-component coating based on epoxy and polyurethane resins; for the coating, waterproofing and elastic protection of roofs, terraces, pavements, stairs, car parks and surfaces that are cracked or subject to micro-cracks and crazing. High wear resistance Applicable on tarred surfaces and bituminous sheaths Walkable product suitable for covering and waterproofing flat roofs Ease and speed of application with quick intervention times Soft and velvety to the touch Elastic product resistant to dynamic stress Available in two colors. Waterproof coating of concrete, ceramic, porcelain stoneware, wood, sheet metal supports, tarred supports and bituminous sheaths, suitably primed. Creation of elastic and waterproof protections for multi-level parking areas, both internal and external. Ideal for waterproofing cycles of balconies, roofs and terraces as it does not require preliminary demolition work or replacement of coverings. Its application allows the creation of a continuous, elastic and waterproof layer resistant to wear and trampling. Approximately 2.0 kg of Syntech Pavicar for each square meter of surface to be covered, in two coats. Can 8.3 kg [A] - Can 16.7 kg [A] - Can 4.17 kg [A] - Can 1.7 kg [B] - Can 3.3 kg [B] - Can 0.83 kg [B] - Kit: 1 Can 4.17 kg [A] + 1 Can 0.83 kg [B] - Kit: 1 Can 8.3 kg [A] + 1 Can 1.7 kg [B] - Kit: 1 Can 16.7 kg [A] + 1 Can 3.3 kg [B]

Syntech Layer Two-component aliphatic polyurethane finish, UV resistant, transparent, in water dispersion, for finishing concrete surfaces and multilayer resin systems. The finish is available in three versions: Glossy, Satin, Matt. The product is suitable for environments with the presence of food, and can therefore be used to protect walls and ceilings that comply with the HACCP protocol, in order to prevent possible food contamination. Excellent mechanical and abrasion resistance Uniform finish Odorless Low maintenance over time Good resistance to UV and yellowing Resistant to atmospheric agents Possible non-slip finish Wide range of transparent finishes available PACKAGING DEPENDING ON THE TYPE OF FINISHING CHOICE: Gloss (Gloss EN ISO 2813: 80 ÷ 90 Gloss Unit) 1 kg kit: 1 can of 0.71 kg [A] + 1 can of 0.29 kg [B] 5 kg kit: 1 x 3.5 kg jar [A] + 1 x 1.5 kg jar [B] 10 kg kit: 1 x 7.1 kg can [A] + 1 x 2.9 kg can [B] Satin (Gloss EN ISO 2813: 30 ÷ 40 Gloss Unit) 1 kg kit: 1 can of 0.77 kg [A] + 1 can of 0.23 kg [B] 5 kg kit: 1 x 3.8 kg jar [A] + 1 x 1.2 kg jar [B] 10 kg kit: 1 x 7.7 kg can [A] + 1 x 2.3 kg can [B] Matt (Gloss EN ISO 2813: < 10 Gloss Unit) 1 kg kit: 1 can of 0.73 kg [A] + 1 can of 0.27 kg [B] 5 kg kit: 1 can of 3.65 kg [A] + 1 can of 1.35 kg [B] 10 kg kit: 1 can of 7.3 kg [A] + 1 can of 2.7 kg [B]. It is used as a smooth or non-slip finish and coating, UV resistant, waterproof, abrasion resistant, for concrete and cementitious substrates subject to mechanical stress Transparent coating for multilayer systems, particularly suitable for industrial floors in car parks, ramps, warehouses, etc. or concrete infrastructures such as bridges, viaducts, silos, tanks, pylons, etc. It can also be applied on steel supports after appropriate preparation and priming of the base Its special odorless formulation makes it particularly suitable for applications in closed environments. Concrete The surfaces to be coated must be stable, clean and free of substances that could affect the adhesion of the coating, such as dirt, grease, oil, residues of coatings and surface treatments, etc. The weak parts must be removed before applying the product by mechanical sanding with diamond discs and vacuum cleaning. The tensile strength of the concrete must not be less than 1.5 N/mm². Resin coatings The surfaces to be covered must be stable, clean and free of substances such as dirt, grease, oil, etc. which can affect the adhesion of the coating. Smooth the surface by mechanical sanding with diamond discs and vacuum. It is recommended to wash the surfaces and let them dry completely before applying the finish. Primers Concrete The application of SYNTECH LAYER must always be preceded by the application of a coat of SYNTECH PAVISHEER water-based epoxy anchoring primer diluted with clean water in the ratio 1:1 by weight. Resin coatings The application of SYNTECH LAYER must always be preceded by sanding the entire surface in order to promote and guarantee optimal adhesion of the product to the support. From 0.10 to 0.13 kg of Syntech Layer for each square meter of surface. Glossy: Tin 3.3 kg [A] - Satin: tin 3.1 kg [A] - matt: tin 2.8 kg [A] - Glossy: Tin 6.7 kg [A] - matt: tin 5.5 kg [A] - Satin: tin 6.2 kg [A] - Glossy: Tin 1.7 kg [B] - matt: tin 2.2 kg [B] - Satin: tin 1.9 kg [B] - Glossy: Tin 3.3 kg [B] - matt: tin 4.5 kg [B] - Satin: tin 3.8 kg [B] - Kit: 1 Glossy: Tin 3.3 kg [A] + 1 Glossy: Tin 1.7 kg [B] - Kit: 1 matt: tin 2.8 kg [A] + 1 matt: tin 2.2 kg [B] - Kit: 1 Satin: tin 3.1 kg [A] + 1 Satin: tin 1.9 kg [B] - Kit: 1 Glossy: Tin 6.7 kg [A] + 1 Glossy: Tin 3.3 kg [B] - Kit: 1 matt: tin 5.5 kg [A] + 1 matt: tin 4.5 kg [B] - Kit: 1 Satin: tin 6.2 kg [A] + 1 Satin: tin 3.8 kg [B]

Syntech IC 55 A two-component pure epoxy adhesive that is fluid with a low viscosity, free from fillers and solvents, being specific for high performance structural consolidation injections in crumbling masonry, degraded concrete, aging screeds and industrial flooring, cracked plasters and mortars and so on. It is ideal for securing bars, clamps and tie-rods. It is also perfect for the deep consolidation of wooden materials and other types of porous materials, with impregnation by brush or roller. Reinforcing and filling injections of cracks in concrete, stone, brick, mixed works etc. Anchor, bonding and attachment of connectors, plates etc. Structural reinforcement and small volume rebuilding (only horizontal) in general. Reinforcement of porous construction materials such as wood, natural stone, bricks etc. The surfaces of application will be seasoned and dry (residual humidity measured at a depth of 4 cm, should not be greater than 4 % ), free from dust, grease, soiling, crumbling and non-adhering parts. Make sure that the environment is well ventilated and wear the personal protective equipment mentioned in the safety data sheet. Add component B to component A taking care to remove all the material from the packaging, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mixture is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous lump-free mixture is obtained. Lay the material using the techniques specific to the type of intervention: injection, pouring, brushing, etc.. Do not apply on wet or pulverised media. Non-conformities of the support can have unpleasant drawbacks: detachments, large bubbles, etc. Apply only in the intended thermal intervention (+8/+35 °C). Use the product immediately after mixing and mix only the amount of product intended for immediate use. Syntech IC 55 is a product based on fluid epoxy resins. It may cause variations in the colour of the product on which it is applied, both wood and stone material. For this reason it is recommended to carry out preliminary tests. Approximately 1.1 kg of SYNTECH IC55 for each cubic decimetre of volume to be filled. Can 1 kg [A] - Can 5 kg [A] - Can 0.5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 1 kg [A] + 1 Can 0.5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B]

Syntech Bioflex Anti-acid coating based on modified epoxy and polysulphide polymers, for the waterproof coating of concrete and steel tanks, tanks and containment tanks. High mechanical and abrasion resistance High adhesion to surfaces Good elasticity High chemical resistance to acids, bases and solvents Very high tenacity and ease of cleaning and maintenance Applicable to heavy thicknesses. Anti-acid waterproofing protective coating for the chemical industry Internal and external lining of tanks, tanks, cisterns, towers, pylons, etc. Waterproof protective coating of digesters of biogas and purification plants Anti-acid protective coating for sewers, secondary tanks, sewer collectors, channels and ducts intended for the containment of waste water and drainage Anti-acid coating of fiberglass tanks for the chemical industry. From 0.40 to 0.50 kg of Syntech Bioflex for each square meter of surface to be covered, applied in two coats. Can 6.1 kg [A] - Can 3.9 kg [B] - Kit: 1 Can 6.1 kg [A] + 1 Can 3.9 kg [B]

Syntech AS 31 The two-component structural epoxy adhesive putty is soft, thixotropic and spatulable (malleable paste), ideal for anchoring steel connectors, hermetically sealing through-holes in concrete, bonding steel plates on concrete surfaces, as an accessory product for laying road joints, for the reconstruction of wooden beam heads, repairing cracks and reconstructing missing geometries, fixing injectors, reconstructing joints in concrete flooring and fixing Elastotex 250 Combi elastic strips, including when in contact with water destined for human consumption. Structural reinforcements of structural elements (beams, pillars, etc.) by bonding steel sheets to the concrete. Reconstruction of joints in concrete floorings. Rigid structural bonding (beton plaque) of prefabricated elements and of articles in different building materials: concrete, steel, glass, wood, marble, tiles, stones etc. Anchoring, bonding and attachment of connectors, ties etc. Attachment of elastic straps for waterproofing joints, Elastotex. Reconstruction of wooden heads, crack repair, reconstruction of missing geometries on various supports. The application surfaces must be suitably prepared and adequately resistant: free from dust, grease, soiling, crumbling and non-adhering parts, devoid of wet surface areas. For floorings, moreover, a shot peening or preliminary milling of the surfaces of adhesion is recommended. The metal elements are to be blasted to "almost white metal". Make sure that the environment is well ventilated and wear the personal protective equipment mentioned in the safety data sheet. Add component B to component A, taking care to remove all the material from the packaging and mixing thoroughly with a mixer at a low number of revolutions (or a suitable manual tool), until a homogeneous mixture is obtained, indicated by the uniform colour and the absence of lumps. Apply to the surfaces with the help of spatulas, trowels, etc. Complete the tasks during the useful life of the product. Do not apply in rainy days; do not apply on moist or wet supports; do not apply on pulverised supports; use the product immediately after mixing. Approximately 1.6 kg of Syntech AS 31 for each cubic decimetre of volume to be grouted. Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B] - Kit: 1 Canister 1 kg [A] + 1 Canister 0.5 kg [B]

Syntech AS 21 Two-component structural adhesive epoxy filler, with soft consistency, thixotropic, easy to spread (malleable paste), for the anchorage of steel connectors, the hermetic closure of through holes in concrete, bonding steel plates on concrete supports, as accessory product for laying road joints, for the reconstruction of wooden heads, crack repair, reconstruction of missing geometries, fixing injectors, reconstruction of joints in concrete floorings etc. Thanks to its soft and thixotropic consistency, Syntech AS 21 has excellent spreadability and is easily applicable even on materials with little or no porous, making it the optimal adhesive for bonding all the elastic bands of our Elastotex line, including the band high elasticity and resistance Elastotex 250 Combi, consisting of a special elastomeric layer in Hypalon. Excellent adhesion also on PVC and plastic materials. Structural reinforcements of structural elements (beams, pillars, etc.) by bonding steel sheets to the concrete. Reconstruction of joints in concrete floorings. Rigid structural bonding (beton plaque) of prefabricated elements and of articles in different building materials: concrete, steel, glass, wood, marble, tiles, stones etc. Anchoring, bonding and attachment of connectors, ties etc. Attachment of elastic straps for waterproofing joints, Elastotex. Reconstruction of wooden heads, crack repair, reconstruction of missing geometries on various supports. The application surfaces must be suitably prepared and adequately resistant: free from dust, grease, soiling, crumbling and non-adhering parts, devoid of wet surface areas. For floorings, moreover, a shot peening or preliminary milling of the surfaces of adhesion is recommended. The metal elements are to be blasted to "almost white metal". Make sure that the environment is well ventilated and wear the personal protective equipment mentioned in the safety data sheet. Add component B to component A, taking care to remove all the material from the packaging and mixing thoroughly with a mixer at a low number of revolutions (or a suitable manual tool), until a homogeneous mixture is obtained, indicated by the uniform colour and the absence of lumps. Apply to the surfaces with the help of spatulas, trowels, etc. Complete the tasks during the useful life of the product. Do not apply in rainy days; do not apply on moist or wet supports; do not apply on pulverised supports; use the product immediately after mixing. Approximately 1.6 kg of Syntech AS 21 for each cubic decimetre of volume to be grouted. Kit: 1 Canister 1 kg [A] + 1 Canister 1 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 5 kg [B]

Smerald Piscine Protective decorative enamel, with satin effect, monocomponent, high technical content, very resistant to the action of UV rays; based on polyurethane polymer mixtures and acrylic modified with Teflon, in aqueous emulsion. Perfect for finishing concrete surfaces intended for permanent contact with water (swimming pools, fountains, ornamental basins, channels, artificial ponds, tanks, etc. ). It is provided in the standard colours Light Blue and White, on request it can be supplied in other colours. Smerald Piscine is a special mixture of polyurethane-acrylate Teflon coated resins, in aqueous emulsion, particularly resistant to light, water, chlorine and the usual sanitising agents. Modified with unalterable high coverage pigments and special additives, effectively protected against UV radiation, assisted by peculiar radical catchers, it is characterised by high adhesion to the support, high elastic performance, excellent coverage capacity with only two coats of application, and absolute absence of toxic solvents of any kind. Specially formulated for painting pools, ornamental basins, channels, fountains, ponds, tanks, and any cement support strongly and permanently in contact with water. The surfaces of application should be clean, free of any soiling, crumbling and non-adhering parts, or non-absorbent, dust, pre-existing paints, etc. Smerald Piscine can be applied by brush, roller or airless (membrane type) with a 1.5 - 2 mm diameter nozzle. It is preferable to wait at least 30 days for the base to mature. Make sure the surface to be treated is dry, mature and free from damp spots. Before proceeding with the application of the paint, it is advisable to wash with a hydro-cleaner to remove dust or loosely adherent residues. As a first coat, the product can be diluted with water at 40/50% in order to uniform and consolidate the base. Leave to dry for 12 hours and then proceed with the application of 2 coats of paint spaced out for at least 12 hours, diluting with water as little as possible. Always apply two coats, spaced at least 12 hours apart, for a consumption of no less than 200 g/m² per coat (about 450 g/m² of total consumption). On large surfaces it is recommended to apply product from the same production batch. Always proceed wet on wet in order to avoid signs of recovery. MAINTENANCE: Maintenance interventions are foreseen, normally every two years, except for special needs. Proceed to detach the old damaged paint, clean the substrate with suitable detergents and remove grease or algae. The damaged areas must be carefully repaired before proceeding with the painting as indicated above. PRECAUTIONS FOR USE: It is recommended to fill the pool at least 15 days after applying the product and to leave the pool full even during the winter or non-use months. The paint is not suitable for use on rubber surfaces, fiberglass swimming pools, concrete with water repellent additives, for particular surfaces it is recommended to carry out a test application on a small area before proceeding with the finish on the entire pool. Apply from 0.30 to 0.50 liters of Smerald Piscine per square metre of surface to be painted. Pail 14 l

Sealpvc RG 250 The Sealpvc RG 250 waterstop is a waterproofing PVC profile that is not hydro-expansive, having a thickness of 25 cm and high elasticity. It is used in static joints for horizontal (slabs) or vertical (elevation walls) constructions, in concrete structures, in the central position of the cast. Given its particular composition, it can be cut with a sharp blade (cutter) and welded with simple heat welding tools, thus making it easier to create connections in the course of work. Waterproofing of static construction joints between: raft foundation and elevation wall, between two raft foundations, between two elevation walls, between the wall and ceiling. Bind with iron wire the side flaps of the waterstop to the steel plates provided, in order to position it and secure it in a central position with respect to the casting to be made. Proceed with the casting operations, ensuring it does not bend nor move from the seat identified. 1 m/m: Use Sealpvc RG 250 welding the two edges of different belts head to head using a leister (manual hot air welder). Roll 25 m

Sealgum Hydro-expanding waterstop sealant with a special mix of natural and synthetic rubbers and hydrophilic agents: in contact with water, it increases up to triple its volume compared to the original size (if used in environments with the presence of sea water the expansion will take place anyway but slightly reduced in volume). Sealgum is a simple waterstop easy to use, not requiring particular preparation on the supports, pre-shaped compartments, etc.. Sealgum waterstops are available in different sections: Sealgum 20.05 = 20x5 mm; Sealgum 20.10 = 20x10 mm; Sealgum 20.20 = 20x20 mm; Sealgum 50.05 = 50x5 mm; Sealgum 100.05 = 100x5 mm. Creation of castings and connections with safe and permanent hydraulic hold. Take care to create the laying site of the waterstop as smooth and even as possible. Remove any flaking, inconsistent, dusty, etc. parts. Sealgum must be spread on the laying surface and fastened using nails (steel nails plus water approx. every 25 cm). Sealing of the joints is ensured by simple placement side by side and not overlapping the ends. Positioning must guarantee good coverage of 10-12 cm by the concrete, to contain the expansive action generated by hydration. For particularly disconnected or rough surfaces, you can position Sealgum with the help of a hydro-expanding sealant in a cartridge Flexseal 300. 1.1 m/m: Use 1 metre of Sealgum for each linear metre, being careful to place 5-10 cm of the product alongside the end/start roll points to guarantee the permanent water tightness of the system. Sealgum 20.05 Roll 10 m - Sealgum 20.10 Roll 10 m - Sealgum 20.20 Roll 5 m - Box: 5 x (Sealgum 20.05 Roll 10 m) - Box: 7 x (Sealgum 20.10 Roll 10 m) - Box: 7 x (Sealgum 20.20 Roll 5 m)

Sanazieg Adhesive high breathability and moldability mortar, based on hydraulic lime, for filling the vanishing points between elements in stone, brick, mouldings, decorative articles etc., in ecological building interventions, new buildings and in the restoration of vintage buildings and monuments. It can be added with earth colours, ornamental aggregates etc. Sanazieg is a product consisting of hydraulic lime, botticino, kaolin, calcium caseinate, Vichy salt, tartaric acid, ammonium salts and natural fibres. It has high hygroscopicity and breathability, contains no cements, resins, solvents and radioemissive substances. Jointing and filling interstices between bricks, or between bricks and stones, in mouldings, and in decorative articles, etc., in interventions of restoration and rehabilitation of old buildings and buildings of historical interest. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer. Gradually add Sanazieg and the water still required, continue to mix until a homogeneous, lump-free mixture of the desired consistency is obtained. The mixing water indicatively necessary is equal to 14%-16% by weight (3.5 - 4 litres per 25 kg bag). Apply with trowel, mechanical plastering machine, etc., in the interstices prepared as specified. To highlight the aggregate, use a sponge or a wet brush as soon as the plaster Sanazieg begins to harden. For more significant removals, spray retardant solutions like PRERIT, immediately after spreading. Approximately 1.6 kg of Sanazieg for each cubic decimetre of volume to be filled (on average 10-15 kg/m² of solid brick masonry to fill). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Sanawarme A thermal, external-coating macroporous plaster with high thermal and acoustic insulation, it has a base of natural hydraulic lime NHL 3.5, natural hydraulic binders with low soluble salt content and low environmental impact, botticino marble, kaolin, calcium casein, Vichy salt, calcium carbonate, tartaric acid, ammonium salts, expanded perlite, cork powder, natural fibres along wth specific and antisaline agents for the dehumidification, thermal and hygrometric restoration of buildings and masonry, in green building works, for new constructions and in the restoration of historic and monumental buildings. Specifically for applying “mineral coatings”. A mortar/plaster with guaranteed performance offering specific insulating properties pursuant to UNI EN 998/1 – Class T1 (the top thermal insulation class). Thermal conductivity certified pursuant to UNI EN 12664. Sanawarme is the highest technological expression of Azichem in the context of renovating plasters. It is a product based on hydraulic lime, botticino, kaolin, calcium caseinate, Vichy salt, calcium carbonate, tartaric acid, ammonium salts, expanded perlite, cork powder and natural fibres. Sanawarme is characterised by high hygroscopic, breathable and thermal/acoustic insulation properties. It is a "thermal mineral coating", natural, for ecological building, that does not contain cements, resins, solvents and radioemissive materials. The structure of the coatings made with Sanawarme, which is particularly suited to quieten and dissipate, in the form of heat, the acoustic energy inside the pores and "channels", provides interesting performance even in terms of sound absorption which, at high frequencies, reaches values of 1/3, with interesting prospects for acoustic correction of the internal environment (Test Report no. 214705 of August 3, 2006 issued by the institute Giordano). Applying coating plasters in both new constructions, and in interventions of restoration and renovation of old buildings. Anti-condensation and mildewcide correction for indoor, out of the ground and buried surfaces. Insulation of thermal bridges. Removal of crumbling plaster, if present. The wall bodies for application should in any case be clean, intact, free from fouling, dust, crumbling and non-adhering parts, conveniently saturated with water until it reaches the condition of "saturated dry surface". In the presence of salt efflorescence it will be necessary to ensure its careful removal by application of packs of the specific acid detergent and saline converter Deterg-A, in solution with water 1:4. To prevent any new spills of salts, use specific universal anti-saline treatments in aqueous solution, Sanareg, for humid surfaces, or solvent-based, FEST SALZ, for cohesive saline concretions but with perfectly dry surfaces. Preliminary construction of specific anchoring scratch coats, breathable, made with Untersana. The rendering, applied by "spraying", must provide a rough, corrugated surface, designed to promote the bonding of the subsequent plaster, which must be applied no later than 2-3 days. In the case of wooden surfaces, attach a galvanized steel wire mesh, diameter 2 mm and mesh 5x5 cm, to the support, holding it away from the surface by 2-3 mm. Spray the rendering Untersana by hand or by plastering machine, in order to provide a rough surface, designed to facilitate the application and the adhesion of Sanawarme. In the case of applying the thermal coat Sanawarme on concrete, it is recommended to apply the super-adhesive rendering Repar Plug. Prepare the plaster, adding Sanawarme, to the mixing water, for approximately 60-70% by weight (8.5 -9 litres per 13 kg bag). Mix thoroughly until it reaches a smooth, creamy, lightweight, lump-free mixture resembling a "compact foam". Apply the thickness required according to the thermal calculation by plastering machine (type PFT model G4, or the like, equipped with lung for light plasters). For small sizes it is also possible to apply it manually with straight edge and plastic mortar. Regularise the plastered surfaces with fine skim Sanastof for ecological buildings, for an indicative consumption of 4 kg/m². "Drown" in the thickness of the finishing layer the fibreglass mesh Armaglass 160. Successive breathable paints or putty coats (from the series SANAFARBE, SANAXIL or PROTECH SIL) can be applied after approximately 28 days; in any case, after the proper curing of the plaster, depending on the actual environmental conditions, and the loss of initial alkalinity. Approximately 4,00 - 4,50 kg/m² of Sanawarme for every centimetre of thickness to be implemented (approximately 420 kg per cubic metre). Bag 13 kg - Pallet: 50 x (Bag 13 kg)

Sanatrock SA Binder mix, additive, to add to the preset quantity of clean and selected sand, to prepare on site for macro-porous, dehumidifying, restorative plasters, in bio-architectural works and renovation of ancient and/or monumental buildings. It is a mix of a high action dehumidifier, ready to use, only mix with water with a NHL natural hydraulic lime base, Botticino, kaolin, silicate and lime aggregates, mineral fibres and specific agents. It is a mix , together with the adequate inert substances, that enables plaster to be created with high breathability, free of cement, resins or solvents and radio-emitting agents, in compliance with bio-architectural parameters. Breathable dehumidifying plaster on the walls (on adding aggregates). Prepare the surface to plaster by removing, if present, the existing plaster, up to a height over approx. 50/100 cm compared to the line of persistent damp. The walls for application should in any case be clean, intact, free of containment, dust, flaking or inconsistent parts, conveniently saturated with water (saturated to dry surfaces). In the presence of saline efflorescence, accurately remove it and give a preventive treatment with a spray application of Sanareg. Then, a subsequent preliminary construction of a rough coat with breathable grip, with the specifically prepared Untersana, or "spraying" (here and there) the same mix as described below. Prepare the plaster by firstly placing in the mixer approx. 2/3 water for the necessary mix, and then respectively adding Sanatrock SA and clean, select sand with the desired granulometry (you are advised to use sand with a maximum diameter of up to 2-3 mm). For packaging in the warehouse, comply with the following use instructions: - kg15 Sanatrock SA - kg 35-40 sand with a max granulomety 2-3 mm. - litres 12-13 of water (the quantity of water can decrease according to the humidity in the sand used). During preparation of the mix, pay attention and add the useful amount of water to obtain an even and creamy mix with the weight/litre of approx 1.3 – 1.5 Kg. This objective is however very easy to reach with minimum attention to the useful mixing time. On the wall, previously make adequate “level stops” (strips are recommended using mortar obtained or wooden boards adequately placed in position and to plumb). Apply the product with a trowel with a total thickness of approx 2-3 cm. Do not carry out any finishing, smoothing or crushing operation with the trowel or the blade of the mortar applied. Strike the “level stops” leaving the surface rough and leave to harden as is. Skim and finish the following day, possibly with the specific Sanastof dehumidifying coat or definitively with a skim coat with a breathability index (μ) under 11. Normally for a building site cement mixer with 200 litres, you are advised to initially add 100 kg of Sanatrock SA, 225 kg of sand and 45 litres of water. During mixing, add water to the mix until you reach the desired consistency (based on the humidity rate of the sand used you may need more or less litres of water). The water normally necessary in the mix is around 16-18% in weight compared to the total weight of the mix (Sanatrock SA + sand). Continue to mix until you obtain an even mix free of lumps. With a 25 kg bag of Sanatrock SA you can normally plaster 3.5 m² of wall at 2 cm thick. Apply the mix obtained using a trowel or plastering machine. Finish with skimming systems that are definitely breathable, such as Sanastof. With no. 1 25 kg bag of Sanatrock SA normally 3.5 m² of wall with 2 cm of thickness can be plastered (see dosage of additional components in the technical data sheet of the product). Bag 15 kg - Pallet 750 kg

Sanatigh This macroporous, breathable, dehumidifying, fibre-reinforced plaster, with a base of natural hydraulic lime NHL 3.5, is for the dehumidification and hygrometric restoration of buildings and masonry, in works on green buildings, for new constructions and in the restoration of historic and monumental buildings. Sanatigh is a product consisting of hydraulic lime, botticino, kaolin, very fine calcium, expanded lightweight aggregates of volcanic origin, fiber-reinforced with special glass microfibres and fibers Readymesh PM 060. It has high hygroscopicity and breathability, contains no cements, resins, solvents and radioemissive substances. It has strong dehumidifying capacities and, thanks to the total absence of cement, is perfectly compatible with all types of masonry and especially with the historical walls and in all the interventions designed according to the canons of green building. Breathable dehumidifying plastering for wall bodies. Removal of crumbling plaster, if present, up to a maximum height of about 1 metre, with respect to the line of persistent humidity; wall bodies of application must in any case be clean, intact, dust-free, fouling, crumbling and non-adhering parts, conveniently saturated with water until they reach the condition of "saturated with dry surface". In the presence of salt efflorescence it will be necessary to ensure it is carefully removed by applying packs of the specific detergent and saline converter Deterg-A, in solution with water of 1:4. To prevent any new spills of salts, use specific universal anti-saline treatments in aqueous solution, Sanareg, for humid surfaces, or solvent-based, FEST SALZ, for cohesive saline concretions but with perfectly dry surfaces. PREPARATION OF THE WALL SURFACE • Remove all inconsistent, friable and rotten material, and grouting from joints, paying utmost attention where they are particularly friable or inconsistent (see also the paragraph on PREPARING SUPPORTS). • In case of strong salt concentrations, read the paragraph on PREPARING SUPPORTS. ROUGH COAT The sprayed rough coat must create a rough, corrugated surface to facilitate the adhesion of the following plaster, which must be applied promptly; within 1 - 2 days from the application of the rough coat. This adhesion spray must be applied with a low thickness (of a few millimetres) using a plastic-fluid consistency, and can be applied with the same Sanatigh product mixed with about 20% water. In case of particularly deteriorated masonry, it is recommended to use a specific Untersana product to make the rough coat. PLASTER The following application of Sanatigh must be made before the complete hardening of the rough coat (within 24-48 hours if the rough coat is made with Sanatigh, and 12-24 hours if made with Untersana). Put about 2/3 of the mixing water into the mixer, and then gradually add Sanatigh and the remaining water, continuing to mix into a homogeneous, lump-free mixture of the desired consistency for trowel or plastering machine application. Indicatively, the necessary mixing water is 16-18% by weight (i.e. 4 - 4.5 litres per 25 kg bag). Application can be performed by manual (trowel, plastering trowel) or mechanical spray methods. In case of application with a plastering machine, in order to allow adequate and homogeneous product mixing, it is recommended to not use machines with a continuous cycle, and to adjust nozzle, air and spray power in order to softly and lightly apply the product without excessive compaction. SKIMMING Levelling of plastered surfaces with Sanastof: green-construction fine, highly breathable mortar, natural hydraulic lime based with special, light, spherical micro-aggregates and high strength microfiber Readymesh PM 060. Protect surfaces from fresh direct exposure to sunlight, from the rain and wind. Cure the prolonged moist hardening. For thicknesses in excess of the 2 cm, and to improve the anti-cracking potential, provide for inserting a suitable reinforcement plaster-holding mesh: ARMAGLASS 140 o, recommended, a galvanized steel wire mesh with 2mm diameter, mesh 5x5 cm. Approximately 13 kg/m² of Sanatigh for every centimetre of thickness to be implemented (minimum thickness 2 cm = 26 kg/m²). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Sanastof Bianco Premixed mineral composition based on natural hydraulic lime NHL 3.5, microsilic with pozzolanic activity, selected aggregates, high tenacity microfibers, light heat-insulating aggregates with low modulus of elasticity. It is used for smoothing and smoothing, both indoors and outdoors. It is perfectly compatible with multiple substrates: lime-based plasters, lime-cement, cement mortars, concretes, porous stone, bricks. Its characteristics make it particularly suitable for green building works and for the restoration of period and monumental buildings. The maximum grain size of the aggregate is 0.9 mm. Sanastof Bianco is a product based on natural hydraulic lime NHL 3.5, kaolin, marble dust, selected siliceous aggregates and light aggregates with a low modulus of elasticity, dimensionally stable. It is a natural product with high intrinsic breathability, without any trace of resins, solvents, diluents and radio-emissive aggregates. The product contains high tenacity microfibers which give great volumetric stability. The special rounded hollow aggregates, dimensionally stable, bring special qualities of thermal insulation, filtering of potentially harmful soluble salts and reduction of the elastic modulus to the shaving. The granulometric curve, the fineness of the binders and some rheological additives of natural origin, make the product particularly smooth during the drafting phase, even when laid on supports with rough or difficult surfaces. The calibrated physical-mechanical characteristics guarantee perfect compatibility on different types of substrates, especially on traditional plasters and mortars. The microsilic content with pozzolanic activity makes smoothing and smoothing performed with Sanastof Bianco highly durable, even in aggressive exposure environments. Quick and easy application on various substrates, such as: transpiring smoothing of wall casings; smoothing on modular wood fiber or calcium silicate coats; regularization of plastered surfaces; leveling of concrete surfaces; regularization and smoothing of repairs carried out with cement mortars; application to mainly thin thicknesses (from 1 to 4 mm) with simultaneous leveling of recesses, imperfections etc. In particularly severe operating conditions it is advisable to interpose, between the first and second coat, the alkali-resistant glass fiber mesh Armaglass 160 (the mesh must be partially drowned on the first still fresh coat of Sanastof Bianco). The breathability, combined with the other physico-chemical characteristics of the product, make the smoothing made with Sanastof an ideal support to accommodate any kind of paint and in particular mineral paints based on potassium silicate or slaked lime. Sanastof is the transpiring smoothing, with a low modulus of elasticity, recommended in all our dehumidifying systems made with the products: Sanatigh, Caleosana, Sanawarme, Unisan, Intosana. The application surfaces must be clean, free from dirt, crumbly and incoherent parts, dust, etc. Smooth substrates must be roughened (roughness> = 1mm). In the event that the support, after cleaning and roughening, is still dusty and crumbly, remove the totally incoherent parts dry with a spatula-brush, or assisting the removal operation with hydro-washing, then consolidate the support by impregnation with aqueous emulsion Protech Fix AC applied in two abundant coats, the second coat immediately before applying Sanastof Bianco with the "fresh on fresh" technique (the consumption of Protech Fix AC for this priming operation is between 120 and 250 gr / m2). Adequately wet the substrate with water before application, anticipating and repeating this operation several times in the case of very porous and absorbent substrates or in hot and arid climates. Approximately 1,3 kg/m² of Sanastof Bianco for each millimetre of thickness to be implemented (on average 3 - 3,5 kg per square metre). Bag 25 kg